simone
Frequent User
Posts: 692
|
Post by simone on Jun 11, 2007 9:56:22 GMT -5
.......or a whole fork set. The front hub on the ET3 is givng me grief and it will be a lot easier to just replace it so does anyone have one they'd sell?
|
|
seans
Frequent User
Posts: 194
|
Post by seans on Jun 11, 2007 10:17:36 GMT -5
do you just need the hub or do you need the spline/berrings and all that crap?
love, sean s
|
|
simone
Frequent User
Posts: 692
|
Post by simone on Jun 11, 2007 10:43:42 GMT -5
I've got all the bearings, break hardware etc, but would also need that race that holds the little back bearing in. It is completely seized in mine, and that little bearing has failed.
|
|
seans
Frequent User
Posts: 194
|
Post by seans on Jun 11, 2007 12:39:37 GMT -5
I'll have a look in the boxes of mystery after work.
I know I have a hub....I think...
love, sean s
|
|
skwirly
Frequent User
one stone's throw from a rock fight
Posts: 128
|
Post by skwirly on Jun 11, 2007 19:20:00 GMT -5
I know Big Chris has one down at Empire because I came across it last week digging through boxes looking for stators. I think I even left it on top, so no digging would be required.
|
|
seans
Frequent User
Posts: 194
|
Post by seans on Jun 11, 2007 21:09:37 GMT -5
No joy Simone, It's a rear hub.
I did however find most of a P2 motor I forgot I had.
just like Christmas.
love, sean s
|
|
rocket
Presidents Club Member
move over the tide wants in.
Posts: 1,431
|
Post by rocket on Jun 13, 2007 0:10:31 GMT -5
hey you wanna swap that p2 motor for a all aluminum moutain bike or a generator.?
|
|
seans
Frequent User
Posts: 194
|
Post by seans on Jun 13, 2007 11:25:14 GMT -5
No
But do you know anybody that needs a Rally stator/ flywheel/ crank...found that too
love, sean s
|
|
simone
Frequent User
Posts: 692
|
Post by simone on Jun 14, 2007 10:07:14 GMT -5
Situation resolved! One of the teamsters at work took it to a chooper buddy and he was able to get the race out with no damage to the thread.
|
|
|
|
Post by Christian on Jun 14, 2007 10:51:46 GMT -5
That is fantastic news.
I think I may still have your bearings if you'd like to come over and grab them. You could just bring the whole fork or hub over if you'd like.
So, are you going to ride it to Seattle now?
|
|
rocket
Presidents Club Member
move over the tide wants in.
Posts: 1,431
|
Post by rocket on Jun 14, 2007 10:59:24 GMT -5
good question that.........
|
|
simone
Frequent User
Posts: 692
|
Post by simone on Jun 14, 2007 11:42:15 GMT -5
I have all the new bearings at home (plus a spare set if anyone is needing them) so those are probably Bonnies after the aborted attempt to change hers.
Jeff and I can't go to Seattle until Friday 11ish and since Jeff's VBB soft seized going to Victoria we don't think that riding to Seattle will be any better for it. And as fun as two up on an ET3 on the highway with Rocket sounds, I think we'll just stick to either a trailer or throwing one in the hatch.
PS I've ridden to Seattle a few times and the way down is great but the way home really sucks. When I have to get up at 6am then next day I won't be too sad about missing that ride home. If I had time off it would be a different story.
|
|
